巩义市华升机械厂
公司简介
我厂位于连霍高速巩义东出口处，东约500米。是生产各种薯类产品的厂家。我厂生产的薯类淀粉加工设备，具有经久耐用、动力小、效率高，省电、省力、用人少，生产加工成本低，对县、乡、村集体和个人都适用。多年来，我厂产品畅销全国各地，深受广大用户好评。
Company profile
I plant is located in Lianhuo highway Gongyi east exit, about 500 meters east. Is the production of various potato products m anufacturers. The potato starch processing equipment produced by our factory has the advantages of durability, sm all power, high efficiency, power saving, village collective and individual. Over the years, our products sell well all over the country and are well received by the m ajority of users.
薯类磨浆分离机是以鲜薯、薯干为主要原料，将这些原料加工成淀粉的一种淀粉加工设备，它一次可以完成粉碎、磨浆、分离三道工序，该机有结构工艺简单，操作方便，省工省力，是一种理想的淀粉加工设备。
华升牌鲜薯淀粉机采用进的锯齿式齿辊，将鲜薯通过高速旋转的齿辊将鲜薯刨成细丝状，且碎渣少，不堵塞过滤网，有利于淀粉的提取，同时锯齿锋利耐磨。淀粉机特殊的浆渣分离装置使刨碎的薯丝通过两次水冲洗，使淀粉和粉渣有足够的时间进行分离，从而提高淀粉的提取率。
操作人员娴熟地掌握设备的性能、机械结构和操作规程后才能上岗作业。操作时，若设备发生故障，应对症采取以下维修和保养措施：
分离机常见故障及排除使用时，磨浆分离机磨片间隙应调整为0.5毫米左右，操作时先拧上部的手柄以使螺旋旋紧，然后回退90度即可；如果刨碎分离和磨浆分离机在工作时出现主轴卡碰，应立即停车检查；若发现轴承损坏应及时更换同型号的轴承；制粉机组工作时，若发现刨碎分离机的电流表长时间处于超载状态，应调整清洗机的喂人量。
特别注意的是：刨碎分离机和磨浆分离机一定要严防铁石等硬杂物进入机内，以免损坏机件。
制粉组合单机上所有的电器设备和传动皮带均不得打湿或进水，以免发生短路或皮带打滑事故；若发现传动皮带打滑应及时调整皮带轮距，使皮带涨紧；清洗机螺旋下的钢丝网使用一定的期限后易损坏，换另一面新齿继续使用；薯类制粉机组停用后，应对整机维修保养，清洗轴承并注足滑润油、脂，所有电器设备均应采取防潮措施，以免影响设备的性能和使用寿命。
Potato refining and separating m achine is a kind of starch processing equipment, which takes fresh potato and dried potato as m ain raw m aterials and processes these raw m aterials into starch. It can complete three processes of crushing, refining and separating at one time. The m achine has s i m p l e structure, convenient operation, labor-saving and labor-saving. It is an ideal starch processing equipment.
Shengtai brand fresh potato starch m achine adopts the sawtooth type toothed roller. The fresh potato will be sliced into fine fila ments through the high-speed rotating toothed roller, which has less slag and does not block the filter screen, which is conducive to the extraction of starch. At the sa me time, the teeth are sharp and wear-resistant, which ensures the continuity of operation. The special separating device of starch m achine m akes the shredded potato go through two times of water washing, so that the starch and the powder residue have enough time to separate, so as to improve the extraction rate of starch.
The operators can only work after m astering the perform ance, mechanical structure and operation rules of the equipment. In case of equipment failure during operation, the following repair and m aintenance measures shall be taken:
and then it can be backed back 90 degrees. If the m ain shaft of the crushing separation and pulp separator collides, the m achine should be stopped for inspection immediately. If the bearing is da m aged, the bearing of the sa me type should be replaced in time; the pulverizing unit works If it is found that the a mmeter of the crushing separator is overloaded for a long time, the feeding a mount of the cleaning m achine should be adjusted.
Calcium based grease should be added once every 48 hours of operation, and the whole m achine should be m aintained regularly once a month;
All electrical equipment and driving belts on the single m achine of pulverizing unit shall not be wet or watered, so as to avoid short circuit or belt slipping accident; if the transmission belt is found to be slipping, the belt wheel gauge shall be adjusted in time to m ake the belt tight; the wire mesh under the screw of the cleaning m achine is easy to be da m aged after a certain period of time, and it shall be renewed after processing 500000 kg of fresh potatoes; the rack of the device on the shaving drum is used to m ake the belt tight After using for a period of time, if it is found that the production efficiency decreases and the powder slag becomes coarse, the rack should be removed and replaced with a new tooth on the other side for continuous use; after the potato flour milling unit is out of service
欢迎来电咨询或到厂考察试机，联系电话13014610089
