东莞市宏阔塑胶有限公司
奥升德,Vydyne,PA66513H,玻纤增强,树脂,注塑级,抗蠕变,高冲击,尺寸稳定,耐化学, 应用于机械、仪器仪表、汽车部件、电子电气、铁路、家电、通讯、纺机、体育休闲用品、油管、油箱, 电子电器：连接器、卷线轴、计时器、护盖断路器、开关壳座、..
PA66物性表 Ascend美国首诺Vydyne R513H物性表
|
Ascend Vydyne? R513H Nylon 66（聚酰胺-尼龙66）
本物性表由中国塑商之家www.plas-cn.com塑料网提供，转载请注明来源！
|
|||
|
Physical Properties物理性质
|
Metric公制数据
|
English英制数据
|
Comments测试方法
|
|
Specific Gravity比重
|
1.22g/cc
|
1.22g/cc
|
ISO 1183
|
|
Water Absorption吸水率
|
1.0 % @Time 86400 sec |
1.0 % @Time 24.0 hour |
ISO 62
|
|
Moisture Absorption at Equilibrium吸湿平衡
|
2.2 %
|
2.2 %
|
50% RH; ISO 62
|
|
Linear Mold Shrinkage线性收缩率
|
0.0050cm/cm @Thickness 2.00 mm |
0.0050in/in @Thickness 0.0787 in |
ISO 294-4
|
|
Linear Mold Shrinkage, Transverse线性收缩率/横向
|
0.010cm/cm @Thickness 2.00 mm |
0.010in/in @Thickness 0.0787 in |
ISO 294-4
|
|
Mechanical Properties力学性能
|
Metric公制数据
|
English英制数据
|
Comments测试方法
|
|
Tensile Strength at Break断裂拉伸强度
|
122MPa
|
17700psi
|
ISO 527
|
|
Elongation at Break断裂伸长率
|
3.0 %
|
3.0 %
|
ISO 527
|
|
Tensile Modulus拉伸模量
|
6.20GPa
|
899ksi
|
ISO 527
|
|
Flexural Strength
|
200MPa
|
29000psi
|
ISO 178
|
|
Flexural Modulus弯曲弹性模量
|
5.20GPa
|
754ksi
|
ISO 178
|
|
Poissons Ratio泊松比
|
0.41
|
0.41
|
ISO 527
|
|
Shear Modulus剪切模量
|
2.20GPa
|
319ksi
|
Calculated
|
|
Izod Impact, Notched悬臂梁缺口冲击强度(ISO)
|
4.70kJ/m2
|
2.24ft-lb/in2
|
ISO 180
|
|
Charpy Impact Unnotched夏比缺口试样冲击
|
2.60J/cm2 @Temperature -30.0 °C |
12.4ft-lb/in2 @Temperature -22.0 °F |
ISO 179
|
|
2.80J/cm2 @Temperature 23.0 °C |
13.3ft-lb/in2 @Temperature 73.4 °F |
ISO 179
|
|
|
Charpy ImPAct, Notched夏比缺口冲击
|
0.790J/cm2 @Temperature -30.0 °C |
3.76ft-lb/in2 @Temperature -22.0 °F |
ISO 179
|
|
0.800J/cm2 @Temperature 23.0 °C |
3.81ft-lb/in2 @Temperature 73.4 °F |
ISO 179
|
|
|
Electrical Properties电性能
|
Metric公制数据
|
English英制数据
|
Comments测试方法
|
|
Volume ResiSTivity体积电阻率
|
4.00e 15ohm-cm @Thickness 3.00 mm |
4.00e 15ohm-cm @Thickness 0.118 in |
IEC 60093
|
|
Dielectric Strength介电强度
|
15.0kV/mm @Thickness 3.00 mm |
381kV/in @Thickness 0.118 in |
IEC 60243
|
|
Arc Resistance耐电弧性
|
60-120sec @Thickness 3.00 mm |
60-120sec @Thickness 0.118 in |
UL 746A
|
|
Comparative Tracking Index跟踪指数
|
400-599V @Thickness 3.00 mm |
400-599V @Thickness 0.118 in |
IEC 60112
|
|
Hot Wire Ignition, HWI热线圈点燃测试
|
7.0-15sec @Thickness 3.00 mm |
7.0-15sec @Thickness 0.118 in |
UL 746A
|
|
7.0-15sec @Thickness 0.710 mm |
7.0-15sec @Thickness 0.0280 in |
UL 746A
|
|
|
15-30sec @Thickness 1.50 mm |
15-30sec @Thickness 0.0591 in |
UL 746A
|
|
|
High Amp Arc Ignition, HAI高电流电弧点燃测试
|
=120arcs @Thickness 0.710 mm |
=120arcs @Thickness 0.0280 in |
UL 746A
|
|
=120arcs @Thickness 1.50 mm |
=120arcs @Thickness 0.0591 in |
UL 746A
|
|
|
=120arcs @Thickness 3.00 mm |
=120arcs @Thickness 0.118 in |
UL 746A
|
|
|
High Voltage Arc-Tracking Rate, HVTR高压电弧跟踪速度
|
10.0-25.4mm/min @Thickness 3.00 mm |
0.394-1.00in/min @Thickness 0.118 in |
UL 746A
|
|
Thermal Properties热性能
|
Metric公制数据
|
English英制数据
|
Comments测试方法
|
|
CTE, linear线性热膨胀系数
|
4.00μm/m-°C @Thickness 2.00 mm, Temperature 23.0 - 55.0 °C |
2.22μin/in-°F @Thickness 0.0787 in, Temperature 73.4 - 131 °F |
ISO 11359
|
|
CTE, linear, Transverse to Flow线性热膨胀系数/横向
|
9.50μm/m-°C @Thickness 2.00 mm, Temperature 23.0 - 55.0 °C |
5.28μin/in-°F @Thickness 0.0787 in, Temperature 73.4 - 131 °F |
ISO 11359
|
|
Melting Point熔点
|
260°C
|
500°F
|
ISO 3146
|
?
