CYCOLAC? Resin INP108

|British

|Metric

|PDF

Americas: COMMERCIAL

SABIC INP108 is a high rubber ABS impact modifier resin, and is based on polybutadiene rubber. Offers superior impact efficiency, especially at low temperatures. Reduces notch sensitivity when alloyed with engineering polymers. Disperses easily. Provides abrasion and chemical resistance to polymers.

Property

TYPICAL PROPERTIES⁽¹⁾
MECHANICAL	Value	Unit	Standard
Hardness, Shore D	58	-	ISO 868
PHYSICAL	Value	Unit	Standard
Specific Gravity	1	-	ASTM D 792
Density (Molded)	1.01	g/cm3	ISO 1183
Mean Resin Particle Size	400	micrometer	SABIC Method
Total NA Volatiles	0.1	%	SABIC Method
Rubber	32	%	SABIC Method

Source GMD, last updated:2010/02/25

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.

    PLEASECONTACT USFOR AVAILABILITY IN YOUR REGION.

    (1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294. 
  

    (2) Only typical data for selection purposes. Not to be used for part or tool design. 
  

    (3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions. 
  

    (4) Internal measurements according to UL standards. 
   
     (5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article. 
    
      (6) Needs hard coat to consistently pass 60 sec Vertical Burn. 
     
Disclaimer :THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( SELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT.Each user is responsible for making its own determination as to the suitability of Seller s materials, products, services or recommendations for the user s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right.
SABIC and brands marked with ? are trademarks of SABIC or its subsidiaries or affiliates.
?2014Saudi Basic Industries Corporation (SABIC). All Rights Reserved.

温馨提示：
我司产品均可免费提供详细物性表(英文和中文版)、加工参数表、ROHS、SGS、MSDS、UL及FDA等认证相关资料；可免费为客户分析样版并提供原料型号咨询服务(可免费帮客户翻译英文资料)；如需试料、了解产品相关信息及当日报价，敬请来电、来邮或在线咨询，我们将竭诚为您服务！