PPA 美国阿莫科 Amodel? A-4145 HH
Amodel? A-4145 HH 物性表
| 基本信息 |
|
| 填料/增强材料 |
|
| 添加剂 |
|
| 特性 |
- 尺寸稳定性良好
- 低吸湿性
- 刚性，良好
- 高强度
- 可激光焊接
- 快的成型周期
- 良好的抗蠕变性
- 耐化学性良好
- 耐热性，高
- 热水可成型性
- 热稳定性
- 润滑
|
| 用途 |
|
| RoHS 合规性 |
|
| 外观 |
|
| 形式 |
|
| 加工方法 |
|
| 多点数据 |
- Isothermal Stress vs. Strain (ISO 11403-1)
|
| 物理性能 |
干燥 |
调节后的 |
单位制 |
测试方法 |
| 密度 |
1.57 |
-- |
g/cm3 |
ISO 1183/A |
| 收缩率 |
|
|
|
ASTM D955 |
| 流动 |
0.40 |
-- |
% |
ASTM D955 |
| 横向流动 |
0.80 |
-- |
% |
ASTM D955 |
| 吸水率(24 hr) |
0.37 |
-- |
% |
ASTM D570 |
| 机械性能 |
干燥 |
调节后的 |
单位制 |
测试方法 |
| 拉伸模量 |
16400 |
-- |
MPa |
ISO 527-2 |
| 拉伸应力 |
|
|
|
ISO 527-2 |
| 断裂, 23°C |
225 |
-- |
MPa |
ISO 527-2 |
| 断裂, 200°C |
70.0 |
-- |
MPa |
ISO 527-2 |
| 断裂, 230°C |
60.0 |
-- |
MPa |
ISO 527-2 |
| 拉伸应变 |
|
|
|
ISO 527-2 |
| 断裂, 23°C |
1.8 |
-- |
% |
ISO 527-2 |
| 断裂, 200°C |
6.1 |
-- |
% |
ISO 527-2 |
| 断裂, 230°C |
6.3 |
-- |
% |
ISO 527-2 |
| 弯曲模量(23°C) |
14500 |
-- |
MPa |
ISO 178 |
| 弯曲应力(23°C) |
325 |
-- |
MPa |
ISO 178 |
| 压缩强度 |
179 |
172 |
MPa |
ASTM D695 |
| 剪切强度 |
89.6 |
75.8 |
MPa |
ASTM D732 |
| 泊松比 |
0.41 |
-- |
|
ASTM E132 |
| 冲击性能 |
干燥 |
调节后的 |
单位制 |
测试方法 |
| 简支梁缺口冲击强度(23°C) |
11 |
-- |
kJ/m2 |
ISO 179/1eA |
| 简支梁无缺口冲击强度(23°C) |
80 |
-- |
kJ/m2 |
ISO 179/1eU |
| 悬壁梁缺口冲击强度(23°C) |
10 |
-- |
kJ/m2 |
ISO 180/1A |
| 无缺口伊佐德冲击强度(23°C) |
65 |
-- |
kJ/m2 |
ISO 180/1U |
| 热性能 |
干燥 |
调节后的 |
单位制 |
测试方法 |
| 热变形温度(1.8 MPa, 未退火) |
297 |
-- |
°C |
ISO 75-2/A |
| 熔融温度 |
327 |
-- |
°C |
ASTM D570, ISO 11357-3 |
| 线形热膨胀系数 |
|
|
|
ASTM E831 |
| 流动 : 0 到 100°C |
2.0E-5 |
-- |
cm/cm/°C |
ASTM E831 |
| 流动 : 100 到 200°C |
1.5E-5 |
-- |
cm/cm/°C |
ASTM E831 |
| 横向 : 0 到 100°C |
7.6E-5 |
-- |
cm/cm/°C |
ASTM E831 |
| 横向 : 100 到 200°C |
1.2E-4 |
-- |
cm/cm/°C |
ASTM E831 |
| 电气性能 |
干燥 |
调节后的 |
单位制 |
测试方法 |
| 体积电阻率 |
2.0E+15 |
5.0E+14 |
ohms·cm |
ASTM D257 |
| 介电强度(1.60 mm) |
20 |
20 |
kV/mm |
ASTM D149 |
| 介电常数 |
|
|
|
ASTM D150 |
| 60 Hz |
3.80 |
4.30 |
|
ASTM D150 |
| 1 MHz |
3.60 |
3.40 |
|
ASTM D150 |
| 耗散因数 |
|
|
|
ASTM D150 |
| 60 Hz |
4.0E-3 |
0.020 |
|
ASTM D150 |
| 1 MHz |
0.012 |
0.019 |
|
ASTM D150 |
| 相比耐漏电起痕指数(CTI) |
600 |
600 |
V |
UL 746 |
| 高电压电弧起痕速率 (HVTR) |
14.0 |
18.0 |
mm/min |
UL 746 |
| 可燃性 |
干燥 |
调节后的 |
单位制 |
测试方法 |
| UL 阻燃等级1(3.20 mm) |
HB |
-- |
|
UL 94 |
| 注射 |
干燥 |
单位制 |
|
| 干燥温度 |
120 |
°C |
|
| 干燥时间 |
4.0 |
hr |
|
| 建议的最大水分含量 |
0.045 |
% |
|
| 料筒后部温度 |
318 到 324 |
°C |
|
| 料筒前部温度 |
327 到 332 |
°C |
|
| 加工（熔体）温度 |
330 到 335 |
°C |
|
| 模具温度 |
65.6 到 93.3 |
°C |
|
| 注射说明 |
| Injection Rate: 3 to 4 in/secHolding Pressure: 50% of injection pressureStorage: Amodel? compounds are shipped in moisture-resistant packages at moisture levels according to specifications. Sealed, undamaged bags should be preferably stored in a dry room at a maximum temperature of 50°C (122°F) and should be protected from possible damage. If only a portion of a package is used, the remaining material should be transferred into a sealable container. It is recommended that Amodel? resins be dried prior to molding following the recommendations found in this datasheet and/or in the Amodel? processing guide. Proper Ventilation: It is strongly recommended that the processing site be correctly ventilated during molding. The ventilation should be placed directly above the injection nozzle to prevent exposure to fumes and gases that may be generated. In the event of a barrel purge where a large melt patty may be generated, it is often advisable to draw the purge patty into a bucket of water to reduce fumes. Hot Runners: Solvay does not encourage the use of hot runner technology with this product. For further clarification on hot runners, please contact your Solvay Specialty Polymers Technical Marketing representative. |
| 备注 |
| 1 . |
These flammability ratings are not intended to reflect hazards presented by these or any other materials under actual fire conditions. |
