苏州寅旭塑化有限公司
Minlon? 10B40 NC010
MINERAL REINFORCED NYLON RESIN
PA66-MD40
CHARACTERISTICS
Regional availability
Processing
Injection Molding
PRODUCT TEXT
Common features of Minlon? nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness /toughness, good high temperature performance, good chemical resistance, paintability, dimensional stability and low warpage.
Grades with improved electrical and flammability properties are available within the Zytel? nylon resin product line. In addition, Minlon? nylon resin is available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses.
The good melt stability of Minlon? nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
Minlon? nylon resin typically is used in demanding applications in the automotive, electrical, electronic, domestic appliances and construction industries.
Minlon? 10B40 NC010 is a 40% mineral reinforced polyamide 66 resin for injection molding.
PRODUCT INFORMATION
DRY/COND.
TEST NORM
Resin Identification
PA66-MD40
ISO 1043
Part Marking Code
>PA66-MD40<
ISO 11469
ISO designation
ISO 16396-PA66,MD40,M1GN,S14-100
-
REGULATORY
Substance of Very High Concern Report
RHEOLOGICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Molding shrinkage, parallel
0.5/-
%
ISO 294-4, 2577
Molding shrinkage, normal
0.9/-
%
ISO 294-4, 2577
MECHANICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Tensile Modulus
9600/5400
MPa
ISO 527-1/-2
Stress at break
92/58
MPa
ISO 527-1/-2
Strain at break
2.5/8
%
ISO 527-1/-2
Flexural Modulus
9000/4800
MPa
ISO 178
Tensile creep modulus, 1h
*/2500
MPa
ISO 899-1
Tensile creep modulus, 1000h
*/1600
MPa
ISO 899-1
Charpy impact strength, 73°F
25/40
kJ/m2
ISO 179/1eU
Charpy impact strength, -22°F
18/17
kJ/m2
ISO 179/1eU
Charpy notched impact strength, 73°F
3/3
kJ/m2
ISO 179/1eA
Charpy notched impact strength, -22°F
2/2
kJ/m2
ISO 179/1eA
Charpy notched impact strength, -40°F
2/2
kJ/m2
ISO 179/1eA
Izod notched impact strength, 73°F
3.5/4
kJ/m2
ISO 180/1A
Izod notched impact strength, -22°F
2.5/2
kJ/m2
ISO 180/1A
Izod notched impact strength, -40°F
2.5/2
kJ/m2
ISO 180/1A
Izod impact strength, 73°F
25/40
kJ/m2
ISO 180/1U
Izod impact strength, -22°F
18/18
kJ/m2
ISO 180/1U
Poisson's ratio
0.34/0.35
-
-
THERMAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Melting temperature, 18°F/min
263/*
°C
ISO 11357-1/-3
Temp. of deflection under load, 260 psi
205/*
°C
ISO 75-1/-2
Temp. of deflection under load, 65 psi
245/*
°C
ISO 75-1/-2
Coeff. of linear therm. expansion, parallel
36/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, normal
66/*
E-6/K
ISO 11359-1/-2
RTI, electrical, 30mil
105
°C
UL 746B
RTI, electrical, 60mil
120
°C
UL 746B
RTI, electrical, 120mil
120
°C
UL 746B
RTI, impact, 30mil
65
°C
UL 746B
RTI, impact, 60mil
105
°C
UL 746B
RTI, impact, 120mil
115
°C
UL 746B
RTI, strength, 30mil
65
°C
UL 746B
RTI, strength, 60mil
115/*
°C
UL 746B
RTI, strength, 120mil
115
°C
UL 746B
FLAMMABILITY
DRY/COND.
UNIT
TEST NORM
Burning Behav. at 60mil nom. thickn.
HB/*
class
IEC 60695-11-10
Thickness tested
1.5/*
mm
IEC 60695-11-10
UL recognition
yes/*
-
UL 94
Burning Behav. at thickness h
HB/*
class
IEC 60695-11-10
Thickness tested
0.71/*
mm
IEC 60695-11-10
UL recognition
yes/*
-
UL 94
Oxygen index
23/*
%
ISO 4589-1/-2
FMVSS Class
B
-
ISO 3795 (FMVSS 302)
Burning rate, Thickness 1 mm
<80
mm/min
ISO 3795 (FMVSS 302)
ELECTRICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Dissipation factor, 100Hz
20/-
E-4
IEC 62631-2-1
Dissipation factor, 1MHz
200/-
E-4
IEC 62631-2-1
Volume resistivity
>1E13/-
Ohm.m
IEC 62631-3-1
Surface resistivity
*/1E15
Ohm
IEC 62631-3-2
Electric strength
30/-
kV/mm
IEC 60243-1
OTHER PROPERTIES
DRY/COND.
UNIT
TEST NORM
Humidity absorption, 80mil
1.6/*
%
Sim. to ISO 62
Water absorption, 80mil
5/*
%
Sim. to ISO 62
Density
1510/-
kg/m3
ISO 1183
INJECTION
DRY/COND.
UNIT
Drying Recommended
yes
Drying Temperature
80
°C
Drying Time, Dehumidified Dryer
2 - 4
h
Processing Moisture Content
≤0.2
%
Melt Temperature Optimum
295
°C
Min. melt temperature
285
°C
Max. melt temperature
305
°C
Max. screw tangential speed
0.2
m/s
Mold Temperature Optimum
100
°C
Min. mold temperature
70
°C
Max. mold temperature
120
°C
Hold pressure range
50 - 100
MPa
Hold pressure time
3
s/mm
Ejection temperature
210
°C
ADDITIONAL INFORMATION
Injection molding
PROCESSING
Flow front speed : 100 mm/s
CHEMICAL MEDIA RESISTANCE
Acids
Acetic Acid (5% by mass), 23°C
Citric Acid solution (10% by mass), 23°C
Lactic Acid (10% by mass), 23°C
Hydrochloric Acid (36% by mass), 23°C
Nitric Acid (40% by mass), 23°C
Sulfuric Acid (38% by mass), 23°C
Sulfuric Acid (5% by mass), 23°C
Chromic Acid solution (40% by mass), 23°C
Bases
Sodium Hydroxide solution (35% by mass), 23°C
Sodium Hydroxide solution (1% by mass), 23°C
Ammonium Hydroxide solution (10% by mass), 23°C
Alcohols
Isopropyl alcohol, 23°C
Methanol, 23°C
Ethanol, 23°C
Hydrocarbons
n-Hexane, 23°C
Toluene, 23°C
iso-Octane, 23°C
Ketones
Acetone, 23°C
Ethers
Diethyl ether, 23°C
Mineral oils
SAE 10W40 multigrade motor oil, 23°C
SAE 10W40 multigrade motor oil, 130°C
SAE 80/90 hypoid-gear oil, 130°C
Insulating Oil, 23°C
