苏州寅旭塑化有限公司
Zytel? 7301 NC010
NYLON RESIN
PA6
CHARACTERISTICS
Regional availability
Processing
Injection Molding, Film Extrusion, Extrusion, Sheet Extrusion, Other Extrusion, Coating
Delivery form
Pellets
PRODUCT TEXT
Zytel? 7301 NC010 is an Unreinforced Polyamide 6
PRODUCT INFORMATION
DRY/COND.
TEST NORM
Resin Identification
PA6
ISO 1043
Part Marking Code
>PA6<
ISO 11469
ISO designation
ISO 16396-PA6,,M1G1N,S14-030
-
REGULATORY
Substance of Very High Concern Report
RHEOLOGICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Viscosity number
150/*1
cm3/g
ISO 307, 1157, 1628
1: Sulfuric acid 96%
MECHANICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Tensile Modulus
2900/1500
MPa
ISO 527-1/-2
Yield stress
80/-
MPa
ISO 527-1/-2
Yield strain
4.5/-
%
ISO 527-1/-2
Nominal strain at break
25/-
%
ISO 527-1/-2
Strain at break, 50mm/min
50/-
%
ISO 527-1/-2
Flexural Modulus
2300/-
MPa
ISO 178
Charpy impact strength, 73°F
N/N
kJ/m2
ISO 179/1eU
Charpy impact strength, -22°F
N/-
kJ/m2
ISO 179/1eU
Charpy impact strength, -40°F
N/-
kJ/m2
ISO 179/1eU
Charpy notched impact strength, 73°F
6/-
kJ/m2
ISO 179/1eA
Izod notched impact strength, 73°F
6/-
kJ/m2
ISO 180/1A
Izod notched impact strength, -40°F
6/-
kJ/m2
ISO 180/1A
Izod impact strength, 73°F
-/N
kJ/m2
ISO 180/1U
Hardness, Rockwell, R-scale
119/-
-
ISO 2039-2
Ball indentation hardness, H 358/30
170/-DS
MPa
ISO 2039-1
Poisson's ratio
0.37/0.43
-
-
Abrasion resistance
4.5/*
mm3
ISO 4649
DS: Derived from similar grade
TRIBOLOGICAL PROPERTIES
DRY/COND.
TEST NORM
Coefficient of static friction, against steel
-/0.22
ASTM 1894
Coefficient of sliding friction, 1h against steel
-/0.26
ASTM 1894
THERMAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Melting temperature, 18°F/min
221/*
°C
ISO 11357-1/-3
Temp. of deflection under load, 260 psi
55/*
°C
ISO 75-1/-2
Temp. of deflection under load, 65 psi
160/*
°C
ISO 75-1/-2
Coeff. of linear therm. expansion, parallel
70/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, normal
100/*
E-6/K
ISO 11359-1/-2
Thermal conductivity solid
0.24
W/(m K)
-
Spec. heat capacity solid
1680
J/(kg K)
-
FLAMMABILITY
DRY/COND.
UNIT
TEST NORM
Glow Wire Flammability Index, 40mil
800/-
°C
IEC 60695-2-12
Glow Wire Flammability Index, 120mil
850/-
°C
IEC 60695-2-12
Glow Wire Ignition Temperature, 30mil
725/-
°C
IEC 60695-2-13
Glow Wire Ignition Temperature, 15mil
725/-
°C
IEC 60695-2-12
Glow Wire Ignition Temperature, 40mil
725/-
°C
IEC 60695-2-13
Glow Wire Ignition Temperature, 60mil
725/-
°C
IEC 60695-2-13
Glow Wire Ignition Temperature, 80mil
725/-
°C
IEC 60695-2-13
Glow Wire Ignition Temperature, 120mil
725/-
°C
IEC 60695-2-13
Glow Wire Temperature, No Flame, 30mil
700/-
°C
IEC 60335-1
Glow Wire Temperature, No Flame, 40mil
700/-
°C
IEC 60335-1
Glow Wire Temperature, No Flame, 60mil
700/-
°C
IEC 60335-1
Glow Wire Temperature, No Flame, 80mil
700/-
°C
IEC 60335-1
Glow Wire Temperature, No Flame, 120mil
700/-
°C
IEC 60335-1
FMVSS Class
B
-
ISO 3795 (FMVSS 302)
Burning rate, Thickness 1 mm
<80
mm/min
ISO 3795 (FMVSS 302)
ELECTRICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Relative permittivity, 1MHz
3.5/7
-
IEC 62631-2-1
Volume resistivity
1E13/1E10
Ohm.m
IEC 62631-3-1
Surface resistivity
*/1E10
Ohm
IEC 62631-3-2
Comparative tracking index
600/600
-
IEC 60112
OTHER PROPERTIES
DRY/COND.
UNIT
TEST NORM
Humidity absorption, 80mil
3/*
%
Sim. to ISO 62
Water absorption, 80mil
9.5/*
%
Sim. to ISO 62
Density
1130/-
kg/m3
ISO 1183
FILM PROPERTIES
DRY/COND.
UNIT
TEST NORM
Stress at yield, parallel
32/*
MPa
ISO 527-3
Stress at yield, normal
31/*
MPa
ISO 527-3
Strain at yield, parallel
18/*
%
ISO 527-3
Strain at yield, normal
18/*
%
ISO 527-3
Maximum stress, parallel
90/*
MPa
ISO 527-3
Maximum stress, normal
80/*
MPa
ISO 527-3
Maximum strain, parallel
350/*
%
ISO 527-3
Maximum strain, normal
400/*
%
ISO 527-3
Gloss, 60°
90/*
-
ISO 2813
Haze
0.02/*
-
ISO 14782
WVTR, 23°C/85%r.h.
15/*
g/(m2*d)
DIS 15106-1/-2
Oxygen transmission rate, 23°C/0%r.h.
12/*
cm3/(m2*d*bar)
DIS 15105-1/-2
Carbon Dioxide transm. rate, 23°C/0%r.h.
45/*
cm3/(m2*d*bar)
DIS 15105-1/-2
Thickness of specimen
0.1/*
mm
-
INJECTION
DRY/COND.
UNIT
Drying Recommended
yes
Drying Temperature
80
°C
Drying Time, Dehumidified Dryer
2 - 4
h
Processing Moisture Content
≤0.2
%
Melt Temperature Optimum
270
°C
Min. melt temperature
260
°C
Max. melt temperature
280
°C
Max. screw tangential speed
0.2
m/s
Mold Temperature Optimum
70
°C
Min. mold temperature
50
°C
Max. mold temperature
90
°C
Hold pressure range
50 - 100
MPa
Hold pressure time
4
s/mm
EXTRUSION
DRY/COND.
UNIT
Drying Temperature
≤80
°C
Drying Time, Dehumidified Dryer
4 - 6
h
Processing Moisture Content
≤0.05
%
Melt Temperature Optimum
235
°C
Melt Temperature Range
230 - 240
°C
CHEMICAL MEDIA RESISTANCE
Acids
Acetic Acid (5% by mass), 23°C
Citric Acid solution (10% by mass), 23°C
Lactic Acid (10% by mass), 23°C
Hydrochloric Acid (36% by mass), 23°C
Nitric Acid (40% by mass), 23°C
Sulfuric Acid (38% by mass), 23°C
Sulfuric Acid (5% by mass), 23°C
Chromic Acid solution (40% by mass), 23°C
Bases
Sodium Hydroxide solution (35% by mass), 23°C
Sodium Hydroxide solution (1% by mass), 23°C
Ammonium Hydroxide solution (10% by mass), 23°C
Alcohols
Isopropyl alcohol, 23°C
Methanol, 23°C
Ethanol, 23°C
Hydrocarbons
n-Hexane, 23°C
Toluene, 23°C
iso-Octane, 23°C
Ketones
Acetone, 23°C
Ethers
Diethyl ether, 23°C
Mineral oils
SAE 10W40 multigrade motor oil, 23°C
SAE 10W40 multigrade motor oil, 130°C
SAE 80/90 hypoid-gear oil, 130°C
Insulating Oil, 23°C
Standard Fuels
ISO 1817 Liquid 1 - E5, 60°C
ISO 1817 Liquid 2 - M15E4, 60°C
ISO 1817 Liquid 3 - M3E7, 60°C
ISO 1817 Liquid 4 - M15, 60°C
Standard fuel without alcohol (pref. ISO 1817 Liquid C), 23°C
Standard fuel with alcohol (pref. ISO 1817 Liquid 4), 23°C
Diesel fuel (pref. ISO 1817 Liquid F), 23°C
Diesel fuel (pref. ISO 1817 Liquid F), 90°C
Diesel fuel (pref. ISO 1817 Liquid F), >90°C
Salt solutions
Sodium Chloride solution (10% by mass), 23°C
Sodium Hypochlorite solution (10% by mass), 23°C
Sodium Carbonate solution (20% by mass), 23°C
Sodium Carbonate solution (2% by mass), 23°C
Zinc Chloride solution (50% by mass), 23°C
Other
Ethyl Acetate, 23°C
Hydrogen peroxide, 23°C
DOT No. 4 Brake fluid, 130°C
Ethylene Glycol (50% by mass) in water, 108°C
1% nonylphenoxy-polyethyleneoxy ethanol in water, 23°C
50% Oleic acid + 50% Olive Oil, 23°C
Water, 23°C
Water, 90°C
Phenol solution (5% by mass), 23°C
