苏州寅旭塑化有限公司
Zytel? 70G33HS1L NC010 / BK031
NYLON RESIN
PA66-GF33
CHARACTERISTICS
Processing
Injection Molding
Special characteristics
Heat stabilized or stable to heat
PRODUCT TEXT
Common features of Zytel? nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel? nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel? nylon resin, including most flame retardant grades, offer the ability to be coloured.
The good melt stability of Zytel? nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
Zytel? nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
Zytel? 70G33HS1L BK031 is a 33% glass fiber reinforced, heat stabilized polyamide 66 resin for injection molding.
PRODUCT INFORMATION
DRY/COND.
TEST NORM
Resin Identification
PA66-GF33
ISO 1043
Part Marking Code
>PA66-GF33<
ISO 11469
ISO designation
ISO 16396-PA66,GF33,M1CGHR,S14-110
-
REGULATORY
Substance of Very High Concern Report
RHEOLOGICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Viscosity number
143/*
cm3/g
ISO 307, 1157, 1628
Molding shrinkage, parallel
0.3/-
%
ISO 294-4, 2577
Molding shrinkage, normal
1.1/-
%
ISO 294-4, 2577
MECHANICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Tensile Modulus
11000/8000
MPa
ISO 527-1/-2
Stress at break
200/140
MPa
ISO 527-1/-2
Strain at break
3/5
%
ISO 527-1/-2
Flexural Modulus
9500/6000
MPa
ISO 178
Flexural Strength
280/195
MPa
ISO 178
Charpy impact strength, 73°F
75/80
kJ/m2
ISO 179/1eU
Charpy notched impact strength, 73°F
13/17
kJ/m2
ISO 179/1eA
Charpy notched impact strength, -40°F
10/10
kJ/m2
ISO 179/1eA
Charpy notched impact strength, -40°C
10/10
kJ/m2
ISO 179/1eA
Izod notched impact strength, 73°F
12/15
kJ/m2
ISO 180/1A
Izod notched impact strength, -40°F
10/10
kJ/m2
ISO 180/1A
Izod impact strength, 73°F
80/-
kJ/m2
ISO 180/1U
Izod impact strength, -22°F
80/-
kJ/m2
ISO 180/1U
Hardness, Rockwell, M-scale
101/-
-
ISO 2039-2
Ball indentation hardness, H 961/30
280/-
MPa
ISO 2039-1
Poisson's ratio
0.34/0.34
-
-
THERMAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Melting temperature, 18°F/min
262/*
°C
ISO 11357-1/-3
Temp. of deflection under load, 260 psi
252/*
°C
ISO 75-1/-2
Temp. of deflection under load, 65 psi
261/*
°C
ISO 75-1/-2
Coeff. of linear therm. expansion, parallel
18/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, normal
83/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, Normal, -40-23°C
65/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, Normal, 55-160°C
140/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, Parallel, -40-23°C
24/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, Parallel, 55-160°C
13/*
E-6/K
ISO 11359-1/-2
RTI, electrical, 30mil
140
°C
UL 746B
RTI, electrical, 60mil
140
°C
UL 746B
RTI, electrical, 120mil
140
°C
UL 746B
RTI, impact, 30mil
125
°C
UL 746B
RTI, impact, 60mil
125
°C
UL 746B
RTI, impact, 120mil
125
°C
UL 746B
RTI, strength, 30mil
140
°C
UL 746B
RTI, strength, 60mil
140/*
°C
UL 746B
RTI, strength, 120mil
140
°C
UL 746B
FLAMMABILITY
DRY/COND.
UNIT
TEST NORM
Burning Behav. at 60mil nom. thickn.
HB/*
class
IEC 60695-11-10
Thickness tested
1.5/*
mm
IEC 60695-11-10
UL recognition
yes/*
-
UL 94
Burning Behav. at thickness h
HB/*
class
IEC 60695-11-10
Thickness tested
0.75/*
mm
IEC 60695-11-10
UL recognition
yes/*
-
UL 94
Glow Wire Flammability Index, 30mil
725/-
°C
IEC 60695-2-12
Glow Wire Flammability Index, 60mil
700/-
°C
IEC 60695-2-12
Glow Wire Flammability Index, 120mil
800/-
°C
IEC 60695-2-12
Glow Wire Ignition Temperature, 30mil
750/-
°C
IEC 60695-2-13
Glow Wire Ignition Temperature, 60mil
725/-
°C
IEC 60695-2-13
Glow Wire Ignition Temperature, 120mil
825/-
°C
IEC 60695-2-13
FMVSS Class
B
-
ISO 3795 (FMVSS 302)
Burning rate, Thickness 1 mm
28
mm/min
ISO 3795 (FMVSS 302)
ELECTRICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Comparative tracking index
400/-
-
IEC 60112
Comparative tracking index
1/-
PLC
UL 746A
Electric Strength, Short Time, 2mm
18/-
kV/mm
IEC 60243-1
OTHER PROPERTIES
DRY/COND.
UNIT
TEST NORM
Humidity absorption, 80mil
1.8/*
%
Sim. to ISO 62
Water absorption, 80mil
5.7/*
%
Sim. to ISO 62
Density
1390/-
kg/m3
ISO 1183
Water Absorption, Immersion 24h
1.2/*
%
Sim. to ISO 62
VDA PROPERTIES
DRY/COND.
UNIT
TEST NORM
Emission of organic compounds
10
μgC/g
VDA 277
Odor test
3
class
VDA 270
Fogging, G-value (condensate)
0.6/*
mg
ISO 6452
INJECTION
DRY/COND.
UNIT
Drying Recommended
yes
Drying Temperature
80
°C
Drying Time, Dehumidified Dryer
2 - 4
h
Processing Moisture Content
≤0.2
%
Melt Temperature Optimum
285
°C
Min. melt temperature
275
°C
Max. melt temperature
2951
°C
Max. screw tangential speed
0.2
m/s
Mold Temperature Optimum
100
°C
Min. mold temperature
70
°C
Max. mold temperature
120
°C
Hold pressure range
50 - 100
MPa
Hold pressure time
3
s/mm
Ejection temperature
210
°C
1: Melt temp can be up to 305C in case of moisture is low and HUT is short.
ADDITIONAL INFORMATION
Injection molding
Maximum hold up time should be 10 minutes.
CHEMICAL MEDIA RESISTANCE
Acids
Acetic Acid (5% by mass), 23°C
Citric Acid solution (10% by mass), 23°C
Lactic Acid (10% by mass), 23°C
Hydrochloric Acid (36% by mass), 23°C
Nitric Acid (40% by mass), 23°C
Sulfuric Acid (38% by mass), 23°C
Sulfuric Acid (5% by mass), 23°C
Chromic Acid solution (40% by mass), 23°C
Bases
Sodium Hydroxide solution (35% by mass), 23°C
Sodium Hydroxide solution (1% by mass), 23°C
Ammonium Hydroxide solution (10% by mass), 23°C
Alcohols
Isopropyl alcohol, 23°C
Methanol, 23°C
Ethanol, 23°C
Hydrocarbons
n-Hexane, 23°C
Toluene, 23°C
iso-Octane, 23°C
Ketones
Acetone, 23°C
Ethers
Diethyl ether, 23°C
Mineral oils
SAE 10W40 multigrade motor oil, 23°C
SAE 10W40 multigrade motor oil, 130°C
SAE 80/90 hypoid-gear oil, 130°C
Insulating Oil, 23°C
Motor oil OS206 304 Ref.Eng.Oil, ISP, 135°C
Automatic hypoid-gear oil Shell Donax TX, 135°C
Hydraulic oil Pentosin CHF 202, 125°C
Standard Fuels
ISO 1817 Liquid 1 - E5, 60°C
ISO 1817 Liquid 2 - M15E4, 60°C
ISO 1817 Liquid 3 - M3E7, 60°C
ISO 1817 Liquid 4 - M15, 60°C
Standard fuel without alcohol (pref. ISO 1817 Liquid C), 23°C
Standard fuel with alcohol (pref. ISO 1817 Liquid 4), 23°C
Diesel fuel (pref. ISO 1817 Liquid F), 23°C
Diesel fuel (pref. ISO 1817 Liquid F), 90°C
Diesel fuel (pref. ISO 1817 Liquid F), >90°C
Salt solutions
Sodium Chloride solution (10% by mass), 23°C
Sodium Hypochlorite solution (10% by mass), 23°C
Sodium Carbonate solution (20% by mass), 23°C
Sodium Carbonate solution (2% by mass), 23°C
Zinc Chloride solution (50% by mass), 23°C
Other
Ethyl Acetate, 23°C
Hydrogen peroxide, 23°C
DOT No. 4 Brake fluid, 130°C
Ethylene Glycol (50% by mass) in water, 108°C
1% nonylphenoxy-polyethyleneoxy ethanol in water, 23°C
50% Oleic acid + 50% Olive Oil, 23°C
Water, 23°C
Water, 90°C
Phenol solution (5% by mass), 23°C
