苏州寅旭塑化有限公司
Zytel? 70G30L NC010
NYLON RESIN
PA66-GF30
CHARACTERISTICS
Processing
Injection Molding
Delivery form
Pellets
Additives
Lubricants, Release agent
PRODUCT TEXT
Common features of Zytel? nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel? nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel? nylon resin, including most flame retardant grades, offer the ability to be coloured.
The good melt stability of Zytel? nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
Zytel? nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
Zytel? 70G30L NC010 is a 30% glass fiber reinforced polyamide 66 resin for injection molding.
PRODUCT INFORMATION
DRY/COND.
TEST NORM
Resin Identification
PA66-GF30
ISO 1043
Part Marking Code
>PA66-GF30<
ISO 11469
ISO designation
ISO 16396-PA66,GF30,M1GNR,S14-100
-
REGULATORY
Substance of Very High Concern Report
RHEOLOGICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Viscosity number
153/*
cm3/g
ISO 307, 1157, 1628
Molding shrinkage, parallel
0.3/-
%
ISO 294-4, 2577
Molding shrinkage, normal
1.1/-
%
ISO 294-4, 2577
MECHANICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Tensile Modulus
10000/7000
MPa
ISO 527-1/-2
Stress at break
190/130
MPa
ISO 527-1/-2
Strain at break
3.5/5
%
ISO 527-1/-2
Charpy impact strength, 73°F
70/80
kJ/m2
ISO 179/1eU
Charpy impact strength, -22°F
60/-
kJ/m2
ISO 179/1eU
Charpy notched impact strength, 73°F
12/15
kJ/m2
ISO 179/1eA
Charpy notched impact strength, -22°F
10/10
kJ/m2
ISO 179/1eA
Izod notched impact strength, 73°F
12/14
kJ/m2
ISO 180/1A
Poisson's ratio
0.34/0.35
-
-
THERMAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Melting temperature, 18°F/min
262/*
°C
ISO 11357-1/-3
Glass transition temperature, 18°F/min
75/20
°C
ISO 11357-1/-2
Temp. of deflection under load, 260 psi
253/*
°C
ISO 75-1/-2
Temp. of deflection under load, 65 psi
260/*
°C
ISO 75-1/-2
Coeff. of linear therm. expansion, parallel
28/*
E-6/K
ISO 11359-1/-2
Coeff. of linear therm. expansion, normal
95/*
E-6/K
ISO 11359-1/-2
Thermal conductivity of melt
0.21
W/(m K)
-
Eff. thermal diffusivity
6.85E-8
m2/s
-
Spec. heat capacity of melt
2290
J/(kg K)
-
RTI, electrical, 30mil
130
°C
UL 746B
RTI, electrical, 60mil
130
°C
UL 746B
RTI, electrical, 120mil
130
°C
UL 746B
RTI, impact, 30mil
120
°C
UL 746B
RTI, impact, 60mil
120
°C
UL 746B
RTI, impact, 120mil
120
°C
UL 746B
RTI, strength, 30mil
130
°C
UL 746B
RTI, strength, 60mil
130/*
°C
UL 746B
RTI, strength, 120mil
130
°C
UL 746B
FLAMMABILITY
DRY/COND.
UNIT
TEST NORM
Burning Behav. at 60mil nom. thickn.
HB/*
class
IEC 60695-11-10
Thickness tested
1.5/*
mm
IEC 60695-11-10
UL recognition
yes/*
-
UL 94
Burning Behav. at thickness h
HB/*
class
IEC 60695-11-10
Thickness tested
0.71/*
mm
IEC 60695-11-10
UL recognition
yes/*
-
UL 94
Oxygen index
24/*
%
ISO 4589-1/-2
FMVSS Class
SE/B
-
ISO 3795 (FMVSS 302)
Burning rate, Thickness 1 mm
24
mm/min
ISO 3795 (FMVSS 302)
ELECTRICAL PROPERTIES
DRY/COND.
UNIT
TEST NORM
Dissipation factor, 100Hz
160/-
E-4
IEC 62631-2-1
Dissipation factor, 1MHz
160/-
E-4
IEC 62631-2-1
Volume resistivity
1E11/-
Ohm.m
IEC 62631-3-1
Surface resistivity
*/1E12
Ohm
IEC 62631-3-2
Comparative tracking index
600/-
-
IEC 60112
Comparative tracking index, 3.0mm
0/-
PLC
UL 746A
OTHER PROPERTIES
DRY/COND.
UNIT
TEST NORM
Humidity absorption, 80mil
2/*
%
Sim. to ISO 62
Water absorption, 80mil
6.9/*
%
Sim. to ISO 62
Density
1370/-
kg/m3
ISO 1183
Density of melt
1210
kg/m3
-
VDA PROPERTIES
DRY/COND.
UNIT
TEST NORM
Emission of organic compounds
6
μgC/g
VDA 277
Thermal desorption analysis of organic emissions
5
μg/g
VDA 278
Odor test
4.5
class
VDA 270
Fogging, F-value (refraction)
95/*
%
ISO 6452
Fogging, G-value (condensate)
0.3/*
mg
ISO 6452
INJECTION
DRY/COND.
UNIT
Drying Recommended
yes
Drying Temperature
80
°C
Drying Time, Dehumidified Dryer
2 - 4
h
Processing Moisture Content
≤0.2
%
Melt Temperature Optimum
295
°C
Min. melt temperature
285
°C
Max. melt temperature
305
°C
Max. screw tangential speed
0.2
m/s
Mold Temperature Optimum
100
°C
Min. mold temperature
70
°C
Max. mold temperature
120
°C
Hold pressure range
50 - 100
MPa
Hold pressure time
3
s/mm
CHEMICAL MEDIA RESISTANCE
Acids
Acetic Acid (5% by mass), 23°C
Citric Acid solution (10% by mass), 23°C
Lactic Acid (10% by mass), 23°C
Hydrochloric Acid (36% by mass), 23°C
Nitric Acid (40% by mass), 23°C
Sulfuric Acid (38% by mass), 23°C
Sulfuric Acid (5% by mass), 23°C
Chromic Acid solution (40% by mass), 23°C
Bases
Sodium Hydroxide solution (35% by mass), 23°C
Sodium Hydroxide solution (1% by mass), 23°C
Ammonium Hydroxide solution (10% by mass), 23°C
Alcohols
Isopropyl alcohol, 23°C
Methanol, 23°C
Ethanol, 23°C
Hydrocarbons
n-Hexane, 23°C
Toluene, 23°C
iso-Octane, 23°C
Ketones
Acetone, 23°C
Ethers
Diethyl ether, 23°C
Mineral oils
SAE 10W40 multigrade motor oil, 23°C
SAE 10W40 multigrade motor oil, 130°C
SAE 80/90 hypoid-gear oil, 130°C
Insulating Oil, 23°C
Standard Fuels
ISO 1817 Liquid 1 - E5, 60°C
ISO 1817 Liquid 2 - M15E4, 60°C
ISO 1817 Liquid 3 - M3E7, 60°C
ISO 1817 Liquid 4 - M15, 60°C
Standard fuel without alcohol (pref. ISO 1817 Liquid C), 23°C
Standard fuel with alcohol (pref. ISO 1817 Liquid 4), 23°C
Diesel fuel (pref. ISO 1817 Liquid F), 23°C
Diesel fuel (pref. ISO 1817 Liquid F), 90°C
Diesel fuel (pref. ISO 1817 Liquid F), >90°C
Salt solutions
Sodium Chloride solution (10% by mass), 23°C
Sodium Hypochlorite solution (10% by mass), 23°C
Sodium Carbonate solution (20% by mass), 23°C
Sodium Carbonate solution (2% by mass), 23°C
Zinc Chloride solution (50% by mass), 23°C
Other
Ethyl Acetate, 23°C
Hydrogen peroxide, 23°C
DOT No. 4 Brake fluid, 130°C
Ethylene Glycol (50% by mass) in water, 108°C
1% nonylphenoxy-polyethyleneoxy ethanol in water, 23°C
50% Oleic acid + 50% Olive Oil, 23°C
Water, 23°C
Water, 90°C
Phenol solution (5% by mass), 23°C
Coolant Glysantin G48, 1:1 in water, 125°C
