东莞市恒磊塑胶有限公司
EL-Lene™ H5615F
Technical Datasheet | Supplied by SCG Chemicals
EL-Lene™ H5615F by SCG Chemicals is a recyclable high density polyethylene (HDPE) grade designed using bimodal technology. Exhibits high tensile strength with good dart impact strength, low gel content, good moisture barrier and high speed processing. EL-Lene™ H5615F is insoluble in water and suitable for processing by blown film extrusion. Recommended for ultra-thin film (<10 micron), roll bag, shopping bag and t-shirt bag. Complies with U.S FDA 21 CFR 177.1520.
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Specific Gravity | 0.956 g/cc | 0.956 g/cc | ASTM D1505 |
| Environmental Stress Crack Resistance | >= 1000 hour @Temperature 50.0 °C |
>= 1000 hour @Temperature 122 °F |
F50, 25% Igepal; ASTM D1693 |
| Thickness | 12.0 microns | 0.472 mil | |
| Melt Flow | 0.15 g/10 min @Load 2.16 kg, Temperature 190 °C |
0.15 g/10 min @Load 4.76 lb, Temperature 374 °F |
ASTM D1238 |
| Mechanical Properties | Metric | English | Comments |
| Film Tensile Strength at Yield, TD | 30.0 MPa | 4350 psi | ASTM D882 |
| Film Elongation at Break, MD | 160 % | 160 % | ASTM D882 |
| Film Elongation at Break, TD | 360 % | 360 % | ASTM D882 |
| Secant Modulus, MD | 0.950 GPa | 138 ksi | ASTM D882 |
| Secant Modulus, TD | 0.980 GPa | 142 ksi | ASTM D882 |
| Elmendorf Tear Strength MD | 3.0 g | 3.0 g | ASTM D1922 |
| Elmendorf Tear Strength TD | 118 g | 118 g | ASTM D1922 |
| Elmendorf Tear Strength, MD | 0.250 g/micron | 6.35 g/mil | ASTM D1922 |
| Elmendorf Tear Strength, TD | 9.83 g/micron | 250 g/mil | ASTM D1922 |
| Dart Drop | 8.90 g/micron | 226 g/mil | ASTM D1709 |
| Dart Drop Test | 107 g | 0.236 lb | ASTM D1709 |
| Film Tensile Strength at Break, MD | 45.0 MPa | 6530 psi | ASTM D882 |
| Film Tensile Strength at Break, TD | 28.0 MPa | 4060 psi | ASTM D882 |
HDPE EL-LENE H5615F 可提供COA、COC,ROHS.MSDS.UL黄卡等等资料，价格最优，质量保证！
基本特性：高密度聚乙烯是一种不透明白色腊状材料，比重比水轻，比重为0.941~0.960，柔软而且有韧性，但比LDPE略硬，也略能伸长，无毒，无味。
燃烧特性：易燃，离火后能继续燃烧，火焰上端呈黄色，下端呈蓝色，燃烧时会熔融，有液体滴落，无黑烟冒出，同时，发出石蜡燃烧时发出的气味。
主要优点：耐酸碱，耐有机溶剂，电绝缘性优良，低温时，仍能保持一定的韧性。表面硬度，拉伸强度，刚性等机械强度都高于LDPE，接近于PP，比PP韧，但表面光洁度不如PP。
主要缺点：机械性能差，透气差，易变形，易老化，易发脆，脆性低于PP，易应力开裂，表面硬度低，易刮伤。难印刷，印刷时，需进行表面放电处理，不能电镀，表面无光泽。
主要用途：
高密度聚乙烯树脂可采用注射、挤出、吹塑和旋转成型等方法成型塑料制品。采用注射成型可成型出各种类型的容器、工业配件、医用品、玩具、壳体、瓶塞和护罩等制品。采用吹塑成型可成型各种中空容器、超薄型薄膜等。采用挤出成型可成型管材、拉伸条带、捆扎带、单丝、电线和电缆护套等。
另外，还可成型建筑用装饰板、百叶窗、合成木材、合成纸、合成膜和成型钙塑制品等 。
