嘉兴华浔电气有限公司
WAS-SSGL
不锈钢电缆防水接头
产品材质：A.C.F部位采用优质304不锈钢制成，B.E部位采用橡胶制成，D部位采用白色尼龙制成。
螺纹规格：公制（M）
工作温度：-40至＋110，短时可达＋120。
产品颜色：A.C.F部位为金属色，B.E部分为黑色，D部分为白色。
防护等级：IP68
产品特性：特殊夹紧爪与密封件相扣之设计，配合迫紧头装配省时便利，夹紧电缆范围大，抗拉力特强，可防水、防尘、防盐、耐酸碱、耐腐蚀、酒精、油、脂。
规格选型：
公制螺纹 (M)
订货号 |
公制螺纹(M) |
卡套范围(mm) |
AG外径(mm) |
GL(mm) |
包装单位(个/包) |
WAS-SSGL-M12 |
M12X1.5 |
3-6 |
12 |
6 |
50 |
WAS-SSGL-M14 |
M14X1.5 |
3-6 |
14 |
6 |
50 |
WAS-SSGL-M16 |
M16X1.5 |
4-8 |
16 |
7 |
50 |
WAS-SSGL-M18 |
M18X1.5 |
6-10 |
18 |
8 |
50 |
WAS-SSGL-M20 |
M20X1.5 |
6-12 |
20 |
8 |
50 |
WAS-SSGL-M22 |
M22X1.5 |
10-14 |
22 |
9 |
50 |
WAS-SSGL-M24 |
M24X1.5 |
10-14 |
24 |
10 |
25 |
WAS-SSGL-M25 |
M25X1.5 |
10-14 |
25 |
10 |
25 |
WAS-SSGL-M27 |
M27X2.0 |
13-18 |
27 |
11 |
25 |
WAS-SSGL-M30 |
M30X2.0 |
13-18 |
30 |
11 |
25 |
WAS-SSGL-M32 |
M32X1.5 |
15-22 |
32 |
11 |
25 |
WAS-SSGL-M33 |
M33X2.0 |
15-22 |
33 |
11 |
20 |
WAS-SSGL-M36 |
M36X2.0 |
18-25 |
36 |
11 |
20 |
WAS-SSGL-M40 |
M40X1.5 |
18-25 |
40 |
11 |
20 |
WAS-SSGL-M42 |
M42X2.0 |
22-28 |
42 |
12 |
20 |
WAS-SSGL-M48 |
M48X2.0 |
25-32 |
48 |
13 |
10 |
WAS-SSGL-M50 |
M50X1.5 |
25-32 |
50 |
13 |
10 |
WAS-SSGL-M54 |
M54X2.0 |
32-38 |
54 |
14 |
10 |
WAS-SSGL-M56 |
M56X2.0 |
32-38 |
56 |
14 |
10 |
WAS-SSGL-M60 |
M60X2.0 |
37-44 |
60 |
14 |
10 |
WAS-SSGL-M63 |
M63X1.5 |
37-44 |
63 |
14 |
10 |
WAS-SSGL-M64 |
M64X2.0 |
37-44 |
64 |
14 |
10 |
WAS-SSGL-M72 |
M72X2.0 |
42-52 |
72 |
15 |
5 |
WAS-SSGL-M80 |
M80X2.0 |
50-60 |
80 |
18 |
5 |
WAS-SSGL-M85 |
M85X3.0 |
59-72 |
85 |
20 |
5 |
WAS-SSGL-M100 |
M100X2.0 |
71-82 |
100 |
22 |
5 |
德制螺纹 (PG)
订货号 |
德制螺纹(PG) |
卡套范围(mm) |
AG外径(mm) |
GL(mm) |
包装单位(个/包) |
WAS-SSGL-PG7 |
PG7 |
3-6 |
12.5 |
8 |
100 |
WAS-SSGL-PG9 |
PG9 |
4-8 |
15.2 |
8 |
100 |
WAS-SSGL-PG11 |
PG11 |
5-10 |
18.6 |
8 |
50 |
WAS-SSGL-PG13.5 |
PG13.5 |
8-12 |
20.4 |
9 |
50 |
WAS-SSGL-PG16 |
PG16 |
10-14 |
22.5 |
10 |
50 |
WAS-SSGL-PG21 |
PG21 |
13-18 |
28.3 |
11 |
50 |
WAS-SSGL-PG29 |
PG29 |
18-25 |
37.0 |
11 |
20 |
WAS-SSGL-PG36 |
PG36 |
25-32 |
47.0 |
13 |
10 |
WAS-SSGL-PG42 |
PG42 |
32-38 |
54.0 |
13 |
10 |
WAS-SSGL-PG48 |
PG48 |
37-44 |
59.3 |
14 |
10 |
英制螺纹 (G)
订货号 |
英制螺纹 (G) |
卡套范围(mm) |
AG外径(mm) |
GL(mm) |
包装单位(个/包) |
WAS-SSGL-G1/4 |
G1/4 |
3-6 |
13.2 |
6 |
100 |
WAS-SSGL-G3/8 |
G3/8 |
4-8 |
16.6 |
7 |
50 |
WAS-SSGL-G1/2 |
G1/2 |
8-12 |
20.4 |
8 |
50 |
WAS-SSGL-G3/4 |
G3/4 |
13-18 |
26.6 |
11 |
50 |
WAS-SSGL-G1 |
G1 |
15-22 |
33.4 |
11 |
50 |
WAS-SSGL-G1-1/4 |
G1-1/4 |
22-28 |
41.5 |
12 |
10 |
WAS-SSGL-G1-1/2 |
G1-1/2 |
25-32 |
47.0 |
13 |
10 |
WAS-SSGL-G2 |
G2 |
37-44 |
60.0 |
14 |
5 |
