Plaslube? PA6 GF10 TL10 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF10 TL10 塑胶原料 Techmer Engineered Solutions


Plaslube? PA6 CF30 TL15 BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 CF30 TS15 BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF10 TL10 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF15 TL15 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF20 RM BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF20 RM L BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF30 RM BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF30 TL15 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF40 ML2 HS UV BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF40 ML5 HS 12MM 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GF40 TL20 BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GL10 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 GL15 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 HS L MB 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 ML2 HS BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 ML2 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 ML3 BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 TL10 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 TL15 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 TL25 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 TS15 BK 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 TS18 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 TSX15 塑胶原料 Techmer Engineered Solutions

Plaslube? PA6 TX10 塑胶原料 Techmer Engineered Solutions

Plaslube? TPX-PA6-03034 塑胶原料 Techmer Engineered Solutions

Plaslube? TPX-PA6-95002 塑胶原料 Techmer Engineered Solutions

　　PA6的化学物理特性和PA66很相似，然而，它的熔点较低，而且工艺温度范围很宽。它的抗冲击性和抗溶解性比PA66要好，但吸湿性也更强。因为塑件的许多品质特性都要收到吸湿性的影响，因此使用PA6设计 产品时要充分考虑这一点。为了提高PA6的机械特性，经常加入各种各样的改性剂。玻璃纤维就是最常见的添加剂，有时为了提高抗冲击性还加入合成橡胶，如EPDM和SBR等。对于没有添加剂的产品，PA6的收缩 1%到1.5%之间。加入玻璃纤维添加剂可以使收缩率降低到0.3%（但和流程相垂直的方向还要稍高一些）。 成型组装的收缩率主要受材料的结晶度和吸湿性影响。实际的收缩率还和塑件设计、壁厚及其它工艺参数成。

我公司长期现货供应塑胶原料:聚酰胺PA6尼龙料,注塑级PA6，防火阻燃级PA6，玻纤增强PA6，防静电PA6、导电PA6、矿物增强PA6、无卤阻燃PA6,耐磨损PA6、抗紫外线耐候级PA6、高刚性尺寸稳定PA6,耐高温高耐热PA6，热稳定级PA6,增韧级PA6,高抗冲击PA6，高润滑PA6,耐寒耐低温PA6，挤出级PA6，FDA食品级PA6，铁氟龙增强PA6，芳纶增强PA6，碳纤增强PA6,医用级PA6。耐寒PA6 PA6耐低温-40度,低温韧性